My Account
sales@megaflex.co.uk
01636 816612
Checkout
0

Rigid (25% Glass Filled) Extruded PTFE Rod in 1m or 2m Lengths


Product Code: RPTFE-25GF-EXT


Rigid 25% Glass Filled Extruded PTFE Rod in 1m or 2m Lengths

Description


Our Extruded Rigid PTFE Rod is available in up to 2m lengths, please email our sales office regarding availability and lead times.

The addition of Glass Fibres improve the wear resistance of the PTFE Rod, and to a minor degree improve the deformation strength under load whilst leaving the substantially unchanged electrical and chemical characteristics.
Glass itself, has a poor resistance to alkalis and is easily attacked by hydrofluoric acid. The coefficient of friction is slightly increased and for this reason, graphite is sometimes added to compensate.

Thermal Properties
PTFE Rod is one of the most thermally stable plastic materials; there is no appreciable decomposition below 400°C. The arrangement of the PTFE molecules varies with temperature. There are different transition points, with the most important ones being 19°C corresponding to a modification of some physical properties, and then at 327°C which corresponds to the disappearance of the crystalline structure; the PTFE Rod assumes an amorphous aspect, conserving its own geometric form.
The linear thermal expansion coefficient varies with temperature. In addition, because of the orientation caused by the working process, the PTFE pieces are in general anisotropic; the coefficient of expansion varies also in relation to direction. The coefficient of thermal conductivity of the PTFE Rod does not vary with temperature; it is relatively high so that PTFE can be considered to be a good insulation material.
The specific heat, as well as the heat content (enthalpy) increases with the temperature.

Chemical Resistance
PTFE is practically inert against known elements and compounds. It is attacked only by the alkaline metals in the elementary state, by Chlorine Trifluoride, and by elementary fluorine at high temperatures and pressures. PTFE is insoluble in almost all solvents at temperatures ip to about 300°C. Fluorinated hydrocarbons cause a certain swelling which is however, reversible. Some highly fluorinated oils, at temperatures over 300°C exercise a certain dissolving effect upon PTFE.
Test pieces of PTFE exposed for over twenty years to the most disparate climate conditions have not shown any alteration of their characteristic properties. High energy radiation tends to cause the breaking of the PTFE molecule, so the resistance to radiation is rather poor. The permeability of PTFE is similar to other plastic materials.

Physical Properties
PTFE can be used continuously at 260°C while still possessing a certain compressive plasticity at temperatures approaching absolute zero. PTFE is quite flexible and does not break when subjected to stresses of 0.7 N/mm2 according to ASTM D 790. Flexural modulus is about 350-650 N/mm2 at room temperature. PTFE possesses very high resilience characteristics at low temperatures. The hardness is Shore D measured according to the method ASTM D 2240; values between D50 and D60.
PTFE possesses the lowest friction coefficients of all solid materials, between 0.05 and 0.09. Additional information can be found in the PTFE material sheets available from our sales office.



Food Quality


  • Suitable for potable water.
  • FDA regulations (Title 21 CFR 177.2600 Part E for aqueous foods).
  • EU Regulation 10/2011 Food Simulant A: Hydrophilic Foods.
  • EU Regulation 10/2011 Food Simulant B: Foods with pH <4.5.
  • EU Regulation 10/2011 Food Simulant C: Alcohol up to 20%.
  • EU Regulation 10/2011 Food Simulant D1: Alcohol content >20% and oil-in-water emulsions.
  • EU Regulation 10/2011 Food Simulant D2: Foods with free fats at the surface.
  • Suitable for alcohol up to 50%.

Temperature


  • -200°C to 260°C

Certification


  • UL 94 V0
  • EU-Directive 10/2011
  • EC 1935/2004
  • EU 2005/1895
  • EU 2023/2006
  • FDA 21 CFR 177.1550
  • DPR777
  • DL108
  • DM 34/73
  • REACH
  • RoHS

Suitable Media


  • Acids
  • Bases
  • Solvents
  • Water
  • Hydrocarbons
  • Salts
  • Gases
  • Chemicals
  • Pharmaceuticals

Applications


  • Mechanical seals
  • Gaskets
  • Bearings
  • Valve seats
  • Insulation spacers
  • Structural components

Construction


  • Wall: PTFE + 25% Glass fiber
  • Surface Finish: Smooth

Available Colours


  • White
PartOuter DiameterLength
RPTFE-25GF-EXT/006-262
RPTFE-25GF-EXT/007-272
RPTFE-25GF-EXT/008-282
RPTFE-25GF-EXT/010-2102
RPTFE-25GF-EXT/012-2122
RPTFE-25GF-EXT/015-2152
RPTFE-25GF-EXT/016-2162
RPTFE-25GF-EXT/018-2182
RPTFE-25GF-EXT/020-2202
RPTFE-25GF-EXT/022-2222
RPTFE-25GF-EXT/025-2252
RPTFE-25GF-EXT/030-2302
RPTFE-25GF-EXT/032-2322
RPTFE-25GF-EXT/035-2352
RPTFE-25GF-EXT/038-2382
RPTFE-25GF-EXT/040-2402
RPTFE-25GF-EXT/045-2452
RPTFE-25GF-EXT/050-2502
RPTFE-25GF-EXT/055-2552
RPTFE-25GF-EXT/060-2602
RPTFE-25GF-EXT/065-2652
RPTFE-25GF-EXT/065-1651
RPTFE-25GF-EXT/070-2702
RPTFE-25GF-EXT/075-2752
RPTFE-25GF-EXT/080-1801
RPTFE-25GF-EXT/080-2802
RPTFE-25GF-EXT/090-1901
RPTFE-25GF-EXT/090-2902
RPTFE-25GF-EXT/100-11001
RPTFE-25GF-EXT/100-21002

Please be advised; specifications assume standard room temperature unless otherwise specified. All data presented here is intended as a guide only; we are not responsible for errors or discrepancies in the specifications. Please click here for full terms and conditions. Please contact our sales office on 01636816612 for further details!