My Account
01636 816612

Rigid 15% Glass and 3% Molybdenum-Disulphide Filled PTFE Rod Extruded Lengths

Product Code: RPTFE-GMOL-EXT

Rigid 15% Glass and 3% Molybdenum-Disulphide Filled PTFE Rod Extruded Lengths


Our Extruded Rigid PTFE Rod is available in up to 2m lengths, please email our sales office regarding availability and lead times.

The addition of Molybdenum Disulphide to the PTFE Rod decreases the coefficient of friction, for which it is sometimes preferred to graphite. Some metal powders including stainless steel, nickel, and titanium are also sometimes used as fillers in consideration of their particular chemical resistances, although their wear resistance are inferior to bronze. The metal oxides added to other fillers often yield better wear properties.

Thermal Properties
PTFE Rod is one of the most thermally stable plastic materials; there is no appreciable decomposition below 400°C. The arrangement of the PTFE molecules varies with temperature. There are different transition points, with the most important ones being 19°C corresponding to a modification of some physical properties, and then at 327°C which corresponds to the disappearance of the crystalline structure; the PTFE Rod assumes an amorphous aspect, conserving its own geometric form.
The linear thermal expansion coefficient varies with temperature. In addition, because of the orientation caused by the working process, the PTFE pieces are in general anisotropic; the coefficient of expansion varies also in relation to direction. The coefficient of thermal conductivity of the PTFE Rod does not vary with temperature; it is relatively high so that PTFE can be considered to be a good insulation material.
The specific heat, as well as the heat content (enthalpy) increases with the temperature.

Chemical Resistance
PTFE is practically inert against known elements and compounds. It is attacked only by the alkaline metals in the elementary state, by Chlorine Trifluoride, and by elementary fluorine at high temperatures and pressures. PTFE is insoluble in almost all solvents at temperatures ip to about 300°C. Fluorinated hydrocarbons cause a certain swelling which is however, reversible. Some highly fluorinated oils, at temperatures over 300°C exercise a certain dissolving effect upon PTFE.
Test pieces of PTFE exposed for over twenty years to the most disparate climate conditions have not shown any alteration of their characteristic properties. High energy radiation tends to cause the breaking of the PTFE molecule, so the resistance to radiation is rather poor. The permeability of PTFE is similar to other plastic materials.

Physical Properties
PTFE can be used continuously at 260°C while still possessing a certain compressive plasticity at temperatures approaching absolute zero. PTFE is quite flexible and does not break when subjected to stresses of 0.7 N/mm2 according to ASTM D 790. Flexural modulus is about 350-650 N/mm2 at room temperature. PTFE possesses very high resilience characteristics at low temperatures. The hardness is Shore D measured according to the method ASTM D 2240; values between D50 and D60.
PTFE possesses the lowest friction coefficients of all solid materials, between 0.05 and 0.09. Additional information can be found in the PTFE material sheets available from our sales office.


  • -200°C to 240°C


  • Slide bearings
  • Bushings
  • Sealing rings
  • Wear strips
  • Guide rails
  • Gasketing material

Suitable Media

  • Acids
  • Alkalis
  • Solvents
  • Gases
  • Water
  • Hydrocarbons


  • Wall: PTFE + 15% Glass fiber + 3% Molybdenum Disulphide
  • Surface Finish: Smooth


  • UL 94 V0
  • RoHS

Available Colours

  • White
PartOuter DiameterLengthColour

Please be advised; specifications assume standard room temperature unless otherwise specified. All data presented here is intended as a guide only; we are not responsible for errors or discrepancies in the specifications. Please click here for full terms and conditions. Please contact our sales office on 01636816612 for further details!